Compact and bijou – my home office!

This content is 8 years old. I don't routinely update old blog posts as they are only intended to represent a view at a particular point in time. Please be warned that the information here may be out of date.

As the Christmas holidays draw to a close (and they have certainly rushed by), I’m reminded to write about how I spent my previous “holiday”. October half term was a busy one as we swapped my eldest son’s bedroom and our home office, redecorating and refitting along the way… or, as I wrote on Facebook at the time:

“1 half term: 9 days of DIY; 3 visits to IKEA; 40+ boxes of flat-packs; 2 trips to the tip; a car full of cardboard; 11 sacks for the bin men…

…a new (smaller) office for us and two happy boys – one with a much bigger bedroom!

Back to work for a rest tomorrow!”

Now, where’s the relevance of all that for my blog? Well, I thought I might write some notes on how we converted the smallest bedroom in the house (approx. 2.15×2.59m) into a reasonable workspace for two people.

Decorating

First up – making good any damage to walls, etc. A plasterer once recommended Gyproc Easi-Fill to me and it’s wonderful stuff. Easy to work with, and sands to a smooth finish.

Next, white paint.

It wasn’t that I didn’t believe Garry Martin’s comment on an earlier post, more that I’d had limited time to prepare and that I thought I’d support a local business instead of my usual decorators merchant. Hey, ho!

Luckily Homebase had an offer on Dulux white emulsion, although I actually used a couple of coats of their own-brand high opacity paint in the end…

Fitting out

With the room repainted (albeit taking more time than I hoped), my attention could turn to fitting things out. My previous office had a length of IKEA Pragel kitchen counter installed as a desk (my son has it in his bedroom now). IKEA don’t make that counter any more, but they do make some good table-tops  (Linnmon) that are very reasonably priced (and also a lot lighter to carry, because the centre filling is basically cardboard – not chipboard).

I needed to cut the table-tops to fit the room and make an L shape, and I also decided to fix them to the wall – lengths of 50x25mm (planed) timber screwed to the wall as battens did the trick there (no need to paint as they are out of sight), with strategically-placed IKEA Adils legs and some brackets to fix the table-tops to the battens (and to hold the table-tops together). The Linnmon tops are also pre-drilled with holes for the Adils legs, which makes things a little easier.  I found some good advice for setting the desk height too.

IKEA Signum desk grommetNext came cable-management. My previous desk had used IKEA Signum desk grommets but they’ve been discontinued. Luckily they are the same size (65mm) as a spare I had from an old desk, so that could be used in my son’s room, whilst I recovered a matching set of 3 for the office.

I also used some IKEA Koppla extension leads with built-in USB ports to provide some above-desk power. Cheaper alternatives are available, but I think they look good screwed to the wall just above the desk.

Shelving came in the form of the ubiquitous Billy bookcase (re-using an existing set of shelves), added to which I put a Bestå frame with a shelf under my desk.  A Stuva wall-cupboard lets me hide away most of my clutter, and some Mosslanda picture ledges finish things off for personal odds and ends around the workspace with a Jansjö LED lamp for desk lighting.

Fixing the cupboard to the wall was a challenge. The wall it’s fixed to is just a stud wall with plasterboard and normal fixings were not really up to the task.  I picked up some 25mm GripIt fixings from my local DIY store that claim to be good for 180kgs each. These fixings (featured on Dragons’ Den) are really strong and easy to use (although drilling a 25mm hole in my wall did fill me with some trepidation at first). I haven’t tested the load up to the full weight but I can say that the cupboard is fixed really solidly now (although I did use some longer M6 bolts to make up for the gap between the back of the cupboard and the wall).

Finally, somewhere to sit. Whilst my wife prefers one of our dining chairs at her desk, I bought a Flintan swivel chair with Nominell armrests (and so far have been very happy with it).

Compact and bijou: my home office
Ignore the apparent curves on the desk – that’s just a dodgy iPhone stitched image!

What next?

I’m trying to keep as little in the room as possible but I think some more bookshelves/another cupboard are inevitable and there’s also the matter of fitting a new blind to the window (on my to-do list, already made to measure by Blinds 2 Go).  I’m also reducing the installed IT: the Cisco 7940 is no longer in use, nor is my old Fujitsu-Siemens S20-1W monitor; and I’m sure Microsoft will want their Lenovo B50 all-in-one PC back soon as I’m doing really badly at writing Windows 10 blog posts (the reason it’s loaned to me), although that means I’ll need to buy another monitor (or two). If you look closely, you’ll also see that I have some work to do tidying some of the cables under the desk…

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.